# Refrigerator Clicking Every 5 Minutes and Not Cooling Diagnosis
Canonical Interactive Tool: https://www.whyitsbroken.com/fix/refrigerator-clicking-every-5-minutes-and-not-cooling-diagnosis
Subsystem: Compressor Electrical & Sealed System Start Circuit | Difficulty: Moderate DIY | Time: 20-45 min | DIY Cost: $15.00-$45.00 (vs Pro $150.00-$340.00)
Empirical Verified Fixes: 1 | Evolution Version: v1

## Direct Answer Summary
When a refrigerator clicks every 5 minutes and fails to cool, the #1 most probable root cause is a failed compressor start relay or overload switch. Confirm this by unplugging the unit, removing the relay near the compressor, and shaking it for rattling. DIY start relay replacement costs $15-$40, versus $150-$340 for a pro service call.

## Ranked Root Causes & Telemetry Signatures
### 1. Faulty Compressor Start Relay (Baseline Probability: 50%)
- **Telemetry Signature:** Normal: Continuity across terminals | Fault: Infinite ohms open circuit or internal rattle
- **Why It Happens:** The electromagnetic start relay uses a spring-loaded plunger or ceramic disc to briefly engage the compressor winding. Over thousands of cycles, the internal contacts pit, weld together, or the ceramic pellet shatters, causing the unit to fail to pass starting current.
- **60-Second Verification Test:** Unplug the refrigerator, remove the access panel behind the compressor, pull the relay straight off the compressor pins, and shake it gently. If you hear rattling, internal components are broken.
- **Resolution Steps:**
  1. Unplug the refrigerator from the 120V wall outlet and wait 5 minutes for capacitors to discharge.
  2. Remove the lower rear cardboard or metal access cover to expose the compressor unit.
  3. Unclip and pull the start relay and overload assembly straight off the three compressor pins.
  4. Install the exact OEM replacement start relay assembly, snapping it securely onto the compressor pins and reconnecting the wire harness.

### 2. Tripped Thermal Overload Protector (Baseline Probability: 22%)
- **Telemetry Signature:** Normal: < 1 Ω continuity | Fault: Permanently open (OL on multimeter)
- **Why It Happens:** The thermal overload switch protects the compressor motor windings from burning out due to excessive draw or high operating temperatures. When it repeatedly trips, it makes an audible click, cuts power, cools down for 5 minutes, and attempts another start.
- **60-Second Verification Test:** Set your digital multimeter to ohms (Ω) and test across the overload protector terminals. A healthy unit reads near 0 ohms; a failed open unit reads infinite resistance (OL).
- **Resolution Steps:**
  1. Disconnect refrigerator power at the wall breaker or outlet.
  2. Remove the combined relay and overload assembly from the side of the compressor.
  3. Test continuity across the overload contacts using a multimeter.
  4. Replace the combined start relay/overload block if the internal bimetal switch has failed permanently open.

### 3. Failed Compressor Run Capacitor (Baseline Probability: 16%)
- **Telemetry Signature:** Normal: Within ±5% rated microfarads (µF) | Fault: Shorted or < 50% rated capacitance
- **Why It Happens:** Some refrigerators utilize a run capacitor to provide continuous phase shift for efficient compressor motor operation. When the capacitor degrades or shorts internally, it draws excessive current, causing the overload relay to trip and click repeatedly.
- **60-Second Verification Test:** Inspect the capacitor exterior for bulging or oil leaks. Test capacitance with a dedicated capacitance meter to verify µF output against rated specifications.
- **Resolution Steps:**
  1. Unplug refrigerator and discharge the run capacitor terminals safely with an insulated resistor tool.
  2. Disconnect wire leads attached to the capacitor spade terminals, noting their exact positions.
  3. Unscrew mounting bracket and remove the defective capacitor.
  4. Mount new capacitor with identical microfarad (µF) and voltage ratings, reconnect leads securely.

### 4. Seized Mechanical Compressor Motor (Baseline Probability: 12%)
- **Telemetry Signature:** Normal: Winding resistance 3–15 Ω | Fault: Windings check good, but motor rotor physically locked
- **Why It Happens:** Internal mechanical components within the sealed compressor unit seize due to lack of lubrication, extreme wear, or electrical surges. The motor attempts to turn, draws locked-rotor amperage (LRA), and immediately trips the thermal overload protector.
- **60-Second Verification Test:** Measure winding resistance across compressor pins (C-S, C-R, S-R). If windings sum correctly but compressor hums and trips overload without spinning, the mechanical pump is locked.
- **Resolution Steps:**
  1. Verify that electrical start components and capacitors are fully functional first.
  2. Clamp ammeter around compressor power lead; observe spike to locked-rotor amperage (e.g., 10A+) preceding the thermal click.
  3. If compressor is mechanically seized, professional refrigerant evacuation and compressor replacement or unit replacement is required.
  4. Compare total repair estimate against replacement cost using our repair calculator.

## Frequently Asked Questions
**Q: Why does my refrigerator click every 5 minutes instead of staying on?**
The 5-minute interval represents the time required for the internal bimetal strip in the thermal overload protector to cool down and reset after tripping. When the compressor fails to start due to a bad relay, current surges, the overload trips, clicks off, cools for 5 minutes, and tries again in an endless loop.

**Q: Can I run my refrigerator if it is clicking and not cooling?**
No, you should unplug the refrigerator immediately. Allowing the compressor to continuously attempt starting with a faulty relay can overheat and permanently burn out the expensive compressor motor windings.

**Q: How do I know if my start relay is bad without tools?**
Unplug the refrigerator, remove the start relay from the side of the compressor, and shake it gently near your ear. If you hear a rattling sound like loose glass or plastic bits, the internal mechanism has disintegrated and must be replaced.

**Q: Is it worth repairing a refrigerator compressor or clicking start relay?**
Replacing a start relay or overload switch is an inexpensive DIY fix ($15-$45) that is almost always worth doing on any refrigerator. However, if the compressor motor itself is seized or the sealed system has a refrigerant leak, professional repairs often exceed $400, making replacement more economical for units over 8 years old.

## External Technical References
- [Refrigerator Clicking Noise? 5 Easy DIY Fixes in 30 Minutes!](https://www.youtube.com/watch?v=awQlM3PsQgo&vl=en)
- [Why Is My Refrigerator Making a Clicking Sound?](https://www.beaconsaves.com/blog/why-is-my-refrigerator-making-a-clicking-sound)
- [Refrigerator Compressor Not Running - iFixit Troubleshooting](https://www.ifixit.com/Troubleshooting/Refrigerator/Compressor+Not+Running/505022)
- [Fridge Clicking Noise and Not Cooling? Expert Troubleshooting Guide](https://www.justanswer.com/appliance/i84dd-fridge-makes-clicking-noise-every-few-minutes.html)
- [How to Troubleshoot a Refrigerator Compressor that Doesn't Start](https://www.youtube.com/watch?v=YAKi-Lw-FpA)
