# Fix Ethernet Adapter Missing From Device Manager on Windows
Canonical Interactive Tool: https://www.whyitsbroken.com/fix/fix-ethernet-adapter-missing-from-device-manager-on-windows
Error Code: `Code 10 / Code 45`
Subsystem: Motherboard PCIe LAN Controller & Windows Network Stack | Difficulty: Easy DIY | Time: 10-30 min | DIY Cost: $0.00-$25.00 (vs Pro $120.00-$250.00)
Empirical Verified Fixes: 1 | Evolution Version: v1

## Direct Answer Summary
An Ethernet adapter missing from Device Manager is most commonly caused by a motherboard power-state latch locking up the PCIe lane (Code 45). Confirm this in under 5 minutes by checking 'Show hidden devices' in Device Manager or performing a 30-second capacitive power drain. DIY cost is $0, compared to a $150+ pro service fee.

## Ranked Root Causes & Telemetry Signatures
### 1. Motherboard PCIe LAN Controller Power Latch Lockup (Baseline Probability: 40%)
- **Telemetry Signature:** Normal: 3.3V VCC / PCIe link active | Fault: 0V standby rail lock, bus enumeration timeout
- **Why It Happens:** Advanced Power Management (APM) or Modern Standby puts the integrated LAN controller into a deep sleep state from which the UEFI/BIOS fails to wake it up during power-on, dropping the device from the PCIe bus entirely.
- **60-Second Verification Test:** Perform a complete hard power drain: shut down PC, unplug the 120V AC power cord, hold the physical power button down for 30 seconds to drain motherboard capacitors, then reboot.
- **Resolution Steps:**
  1. Shut down Windows completely and unplug the power cable from the back of the power supply.
  2. Press and hold the PC front power button for 30 seconds to bleed residual capacitance from motherboard circuits.
  3. Disconnect all external USB devices and Ethernet cables.
  4. Plug the AC power cord back in and boot directly into UEFI/BIOS to verify if the onboard LAN is enabled.

### 2. Corrupted Driver INF File & Windows Code 45 State (Baseline Probability: 30%)
- **Telemetry Signature:** Normal: Driver loaded (e.g. e1dexpress.sys) | Fault: Registry key corruption, Code 45 orphaned device
- **Why It Happens:** A sudden power outage, faulty Windows update, or driver crash corrupts the driver registry hive or leaves an orphaned ghost instance of the device in the device tree.
- **60-Second Verification Test:** Open Device Manager, click View > Show hidden devices, expand Network adapters, and check for a faded/greyed-out Ethernet entry.
- **Resolution Steps:**
  1. Open Device Manager, navigate to View, and select 'Show hidden devices'.
  2. Right-click any greyed-out Ethernet adapter and select 'Uninstall device'.
  3. Download the latest vendor LAN driver (Intel, Realtek) from the official motherboard manufacturer support page using another device.
  4. Install the driver package and restart your computer to force hardware re-enumeration.

### 3. UEFI/BIOS LAN Controller Disabled or Corrupted NVRAM (Baseline Probability: 18%)
- **Telemetry Signature:** Normal: BIOS LAN setting [Enabled] | Fault: BIOS LAN setting [Disabled] or NVRAM config corruption
- **Why It Happens:** BIOS settings can occasionally reset due to a failing CMOS coin cell battery or an erroneous update, toggling the onboard LAN controller chip to 'Disabled' in the motherboard firmware.
- **60-Second Verification Test:** Reboot the PC and tap F2 or DEL to enter BIOS settings; look under 'Advanced' or 'Peripherals' to verify Onboard LAN Controller status.
- **Resolution Steps:**
  1. Reboot your computer and enter the UEFI/BIOS utility during the splash screen.
  2. Navigate to Advanced, Integrated Peripherals, or Onboard Devices configuration.
  3. Locate 'Onboard LAN Controller' or 'MAC LAN' and ensure it is set to [Enabled].
  4. Save changes and exit (F10), allowing Windows to boot fresh.

### 4. Physical Controller Hardware Failure or ESD Damage (Baseline Probability: 12%)
- **Telemetry Signature:** Normal: PHY chip temp 35-45°C, 3.3V rail stable | Fault: PHY chip dead short, 0V across isolation transformer
- **Why It Happens:** Electrical surges passing through the Ethernet cable from a nearby lightning strike or electrostatic discharge (ESD) can fry the onboard physical layer (PHY) transceiver chip.
- **60-Second Verification Test:** Inspect Ethernet port with a flashlight for bent pins, verify link lights remain dark across multiple known-working cables and different routers.
- **Resolution Steps:**
  1. Confirm motherboard LAN failure persists across BIOS resets, driver reinstalls, and hard power drains.
  2. Power down PC, unplug AC power, and ground yourself against ESD before opening the chassis.
  3. Install a dedicated PCIe Gigabit Ethernet network card into an available PCIe x1 slot.
  4. Boot into Windows, install drivers for the new PCIe card, and connect your Ethernet cable.

## Frequently Asked Questions
**Q: Why did my Ethernet adapter suddenly disappear without any software updates?**
This is typically caused by the motherboard's Advanced Power Management (APM) putting the LAN controller chip into a deep sleep state from which it failed to wake. Performing a complete 30-second power drain resets the PCIe bus state and restores detection.

**Q: What is Error Code 45 in Device Manager?**
Error Code 45 indicates that Windows is currently unable to connect the hardware device to the system because the physical device is either disconnected or its driver entry has become orphaned in the Windows device registry.

**Q: Can a bad Ethernet cable cause the adapter to disappear from Device Manager?**
No. A bad cable or dead router port will cause a 'Network cable unplugged' or 'Unidentified network' error, but the adapter itself will still remain fully visible and listed inside Windows Device Manager.

**Q: What should I do if the onboard LAN port is permanently dead?**
If electrostatic discharge or a power surge has fried the integrated Ethernet chip, you do not need to replace the entire motherboard. You can simply install an inexpensive PCIe Gigabit network card into an open PCIe slot on your motherboard.

## External Technical References
- [Ethernet Wired adapter missing - Microsoft Q&A](https://learn.microsoft.com/en-us/answers/questions/5606403/ethernet-wired-adapter-missing)
- [How to Fix Windows 10 Network Adapter Missing... | CloudHouse](https://cloudhousetechnologies.com/blog/fix-windows-10-network-adapter-missing-ethernet-driver)
- [How To Fix Network Adapter Not Showing In Device Manager](https://www.youtube.com/watch?v=pEJ-TXlnPaY)
- [Question - Network Adapter (LAN) has disappeared from Device Manager ? | Tom's Hardware Forum](https://forums.tomshardware.com/threads/network-adapter-lan-has-disappeared-from-device-manager.3844092)
- [How to fix a missing network adapter in Device Manager? - Facebook](https://www.facebook.com/groups/meltonresidents/posts/23920278464299354)
