# Diagnosing Ecobee Smart Thermostat Reboots During Furnace Heating
Canonical Interactive Tool: https://www.whyitsbroken.com/fix/diagnosing-ecobee-smart-thermostat-reboots-during-furnace-heating
Subsystem: HVAC 24VAC Low-Voltage & Gas Furnace Safety Control Circuit | Difficulty: Moderate DIY | Time: 15-45 min | DIY Cost: $0.00-$45.00 (vs Pro $150.00-$340.00)
Empirical Verified Fixes: 1 | Evolution Version: v1

## Direct Answer Summary
An Ecobee thermostat rebooting specifically when the furnace calls for heat is most commonly caused by an open high-limit safety switch or a 24VAC voltage sag below 20V. Confirm this by checking transformer voltage at R and C during a burn cycle. DIY fix costs $0-$45; professional service runs $150-$340.

## Ranked Root Causes & Telemetry Signatures
### 1. Furnace High-Limit Switch Interruption (Baseline Probability: 45%)
- **Telemetry Signature:** Normal: 24VAC across R-C during call | Fault: 0VAC drops to thermostat when limit opens, opening R-W loop
- **Why It Happens:** Restricted airflow (dirty filter, blocked vents) causes heat exchanger temperature to exceed safe limits (typically 180°F–300°F). The bimetallic high-limit safety switch opens, cutting 24VAC power to the thermostat wiring in older furnace configurations, forcing a hard reboot.
- **60-Second Verification Test:** Inspect air filter and temporarily run furnace with filter removed. Use a multimeter to check continuity across limit switch terminals when hot.
- **Resolution Steps:**
  1. Turn off 120V power switch at the furnace and trip main breaker if needed.
  2. Remove furnace service door and locate the bimetallic high-limit safety switch near the heat exchanger plenum.
  3. Inspect switch terminals for corrosion and check continuity with a multimeter.
  4. Replace clogged air filter with a standard pleated filter and test heating cycle.

### 2. Transformer Voltage Sag Under Load (Baseline Probability: 25%)
- **Telemetry Signature:** Normal: 24V–28V AC idling / >21V under load | Fault: Drops below 19.5V AC when inducer/gas valve activate
- **Why It Happens:** The HVAC transformer is undersized (e.g., 20VA/30VA) or degrading. When multiple inductive loads like the inducer motor, gas valve, and smart thermostat draw current simultaneously, secondary voltage sags below the Ecobee's 20V minimum operating threshold, causing a reboot.
- **60-Second Verification Test:** Measure AC voltage across R and C terminals at the furnace control board while the furnace is actively running a heating cycle.
- **Resolution Steps:**
  1. Turn off power to furnace at the breaker panel.
  2. Disconnect old transformer leads from 120V line voltage and 24V control board.
  3. Mount replacement 40VA 24VAC HVAC transformer and secure wire connections.
  4. Verify secondary output measures between 24V and 28V AC idle.

### 3. Unstable C-Wire Resistance or Loose Terminal (Baseline Probability: 18%)
- **Telemetry Signature:** Normal: < 1.0 Ω loop resistance on C wire | Fault: Intermittent open or > 5.0 Ω resistance under vibration
- **Why It Happens:** The Common (C) wire supplying continuous power to the Ecobee has a loose screw terminal at the furnace control board or thermostat backplate, or suffers from high resistance due to corrosion. Blower vibration during a heat call creates an open circuit, dropping power.
- **60-Second Verification Test:** Wiggle thermostat wire bundle at furnace control board while monitoring Ecobee power status for sudden reboots.
- **Resolution Steps:**
  1. Shut off power to furnace and thermostat.
  2. Strip 1/4 inch of fresh copper on the C wire at both thermostat and control board ends.
  3. Securely tighten screw terminals on both the furnace board and Ecobee backplate.
  4. Restore power and verify stable voltage on the Ecobee screen.

### 4. Faulty Power Extender Kit (PEK) Installation (Baseline Probability: 12%)
- **Telemetry Signature:** Normal: Steady 24V pulses on PEK terminal | Fault: Voltage interruption during simultaneous W and Y relay closure
- **Why It Happens:** When a 4-wire installation uses the Ecobee Power Extender Kit (PEK), incorrect wiring terminal connections or a faulty PEK module can cause power multiplexing failures when both heating and fan relays energize.
- **60-Second Verification Test:** Inspect PEK wiring terminals at furnace control board against Ecobee installation manual color-coding guide.
- **Resolution Steps:**
  1. Power down furnace completely.
  2. Verify PEK wires (R, C, W, Y) match furnace board terminals (R, C, W/W1, Y/Y1) exactly.
  3. Re-secure wire nuts connecting thermostat wires to PEK pigtails.
  4. Test heating call to ensure PEK maintains uninterrupted power delivery.

## Frequently Asked Questions
**Q: Why does my Ecobee only reboot when the furnace turns on?**
When the furnace starts, it draws low-voltage power for the gas valve, inducer motor, and safety switches. If your transformer is weak or airflow restriction trips the high-limit switch, 24VAC power to the thermostat drops below the minimum operating threshold, causing a reboot.

**Q: Can a dirty air filter cause an Ecobee to restart?**
Yes. A clogged filter restricts airflow over the heat exchanger, causing internal furnace temperatures to spike. This trips the safety high-limit switch, which interrupts power to the thermostat circuit in many traditional furnace wiring layouts.

**Q: Do I need a C-wire to prevent Ecobee reboots?**
Yes. While Ecobee can 'steal' power across R and W without a C-wire in simple heating systems, this method frequently fails when modern heating relays engage, leading to voltage sags and unexpected reboots. Installing a dedicated C-wire or PEK resolves this.

**Q: What should my multimeter read when testing furnace transformer voltage?**
When the furnace is idling, you should measure between 24V and 28V AC across the R and C terminals. During an active heating call, voltage should remain above 21V AC; if it drops below 19.5V AC, the transformer or load is faulty.

## External Technical References
- [How to: Overheating Furnace Restarting (Smart Thermostat) DIY Tutorial [Ecobee Rebooting] 💯😁](https://www.youtube.com/watch?v=Gmdeltbcx1Q)
- [Introducing ecobee’s Newest Pro-Exclusive Smart Thermostat: ecobee Smart Thermostat Lite | GNRC Stock News](https://www.stocktitan.net/news/GNRC/introducing-ecobee-s-newest-pro-exclusive-smart-thermostat-ecobee-7ulhhjs5zjre.html)
- [Introducing ecobee by Generac Smart Thermostat Enhanced with Home Energy Management](https://finance.yahoo.com/news/introducing-ecobee-generac-smart-thermostat-113000671.html)
- [ecobee and Rheem launch EcoNet smart thermostat | GNRC Stock News](https://www.stocktitan.net/news/GNRC/rheem-and-ecobee-partner-to-launch-the-ecobee-smart-thermostat-lite-dx7ikt8hpi55.html)
- [Rheem® and ecobee partner to launch the ecobee Smart Thermostat Lite | Works with EcoNet® Technology](https://finance.yahoo.com/news/rheem-ecobee-partner-launch-ecobee-141500597.html)
